4.12 Interlocks

Until now, we assumed that a master can run builds at any slave whenever needed or desired. Some times, you want to enforce additional constraints on builds. For reasons like limited network bandwidth, old slave machines, or a self-willed data base server, you may want to limit the number of builds (or build steps) that can access a resource.

Access Modes

The mechanism used by Buildbot is known as the read/write lock.¹ It allows either many readers or a single writer but not a combination of readers and writers. The general lock has been modified and extended for use in Buildbot. Firstly, the general lock allows an infinite number of readers. In Buildbot, we often want to put an upper limit on the number of readers, for example allowing two out of five possible builds at the same time. To do this, the lock counts the number of active readers. Secondly, the terms read mode and write mode are confusing in Buildbot context. They have been replaced by counting mode (since the lock counts them) and exclusive mode. As a result of these changes, locks in Buildbot allow a number of builds (upto some fixed number) in counting mode, or they allow one build in exclusive mode.

Note that access modes are specified when a lock is used. That is, it is possible to have a single lock that is used by several slaves in counting mode, and several slaves in exclusive mode. In fact, this is the strength of the modes: accessing a lock in exclusive mode will prevent all counting-mode accesses.

Count

Often, not all slaves are equal. To allow for this situation, Buildbot allows to have a separate upper limit on the count for each slave. In this way, you can have at most 3 concurrent builds at a fast slave, 2 at a slightly older slave, and 1 at all other slaves.

Scope

The final thing you can specify when you introduce a new lock is its scope. Some constraints are global – they must be enforced over all slaves. Other constraints are local to each slave. A master lock is used for the global constraints. You can ensure for example that at most one build (of all builds running at all slaves) accesses the data base server. With a slave lock you can add a limit local to each slave. With such a lock, you can for example enforce an upper limit to the number of active builds at a slave, like above.

Examples

Time for a few examples. Below a master lock is defined to protect a data base, and a slave lock is created to limit the number of builds at each slave.

     from buildbot import locks
     
     db_lock = locks.MasterLock("database")
     build_lock = locks.SlaveLock("slave_builds",
                                  maxCount = 1,
                                  maxCountForSlave = { 'fast': 3, 'new': 2 })

After importing locks from buildbot, db_lock is defined to be a master lock. The "database" string is used for uniquely identifying the lock. At the next line, a slave lock called build_lock is created. It is identified by the "slave_builds" string. Since the requirements of the lock are a bit more complicated, two optional arguments are also specified. The maxCount parameter sets the default limit for builds in counting mode to 1. For the slave called 'fast' however, we want to have at most three builds, and for the slave called 'new' the upper limit is two builds running at the same time.

The next step is accessing the locks in builds. Buildbot allows a lock to be used during an entire build (from beginning to end), or only during a single build step. In the latter case, the lock is claimed for use just before the step starts, and released again when the step ends. To prevent deadlocks,² it is not possible to claim or release locks at other times.

To use locks, you add them with a locks argument to a build or a step. Each use of a lock is either in counting mode (that is, possibly shared with other builds) or in exclusive mode, and this is indicated with the syntax lock.access(mode), where mode is one of "counting" or "shared".

A build or build step proceeds only when it has acquired all locks. If a build or step needs a lot of locks, it may be starved³ by other builds that need fewer locks.

To illustrate use of locks, a few examples.

     from buildbot import locks
     from buildbot.steps import source, shell
     from buildbot.process import factory
     
     db_lock = locks.MasterLock("database")
     build_lock = locks.SlaveLock("slave_builds",
                                  maxCount = 1,
                                  maxCountForSlave = { 'fast': 3, 'new': 2 })
     
     f = factory.BuildFactory()
     f.addStep(source.SVN(svnurl="http://example.org/svn/Trunk"))
     f.addStep(shell.ShellCommand(command="make all"))
     f.addStep(shell.ShellCommand(command="make test",
                                  locks=[db_lock.access('exclusive')]))
     
     b1 = {'name': 'full1', 'slavename': 'fast',  'builddir': 'f1', 'factory': f,
            'locks': [build_lock.access('counting')] }
     
     b2 = {'name': 'full2', 'slavename': 'new',   'builddir': 'f2', 'factory': f.
            'locks': [build_lock.access('counting')] }
     
     b3 = {'name': 'full3', 'slavename': 'old',   'builddir': 'f3', 'factory': f.
            'locks': [build_lock.access('counting')] }
     
     b4 = {'name': 'full4', 'slavename': 'other', 'builddir': 'f4', 'factory': f.
            'locks': [build_lock.access('counting')] }
     
     c['builders'] = [b1, b2, b3, b4]

Here we have four slaves b1, b2, b3, and b4. Each slave performs the same checkout, make, and test build step sequence. We want to enforce that at most one test step is executed between all slaves due to restrictions with the data base server. This is done by adding the locks= parameter with the third step. It takes a list of locks with their access mode. In this case only the db_lock is needed. The exclusive access mode is used to ensure there is at most one slave that executes the test step.

In addition to exclusive accessing the data base, we also want slaves to stay responsive even under the load of a large number of builds being triggered. For this purpose, the slave lock called build_lock is defined. Since the restraint holds for entire builds, the lock is specified in the builder with 'locks': [build_lock.access('counting')].

Note that you will occasionally see lock.access(mode) written as LockAccess(lock, mode). The two are equivalent, but the former is preferred.